Allmand Vertical Tower V Series Bedienungsanleitung

11 NIGHT-LITE PRO V SERIESVERTICAL TOWEROPERATOR’S MANUALALLMAND BROS. INCP.O. BOX 888HOLDREGE, NE 68949PHONE: 308/995-4495, 1-800/562-1373ALLMAND FA

1010HYDRAULIC LIFT VERTICAL MAST OPERATIONDESCRIPTION OF OPERATIONThe Allmand NIGHT-LITE V Series hydraulic lift tower assembly consists of a seven se

101011HYDRAULIC LIFT VERTICAL MAST OPERATION VISUALLY INSPECT EQUIPMENT FOR DAMAGE BEFORE OPERATING. ALLOW ADEQUATE CLEARANCE AROUND TRAIL-ER FOR T

1212POWER UNIT INSTALLATION & START UP PROCEDUREFill the reservoir with automatic transmission uid or any clean hydraulic uid having aviscosity

1212131. Make sure the corner guide block cover plate is on top of the UHMW (plastic) corner friction block and a 3/8 internal star washer is between

1414TO ERECT MAST AND RAISE LIGHTS1. Extend both side outrigger jacks and tongue jack to stabilize and level the trailer.NOTE: Jacks should be placed

141415SPECIFICATIONSLow oil pressure and high engine temperature shut-downs are standard equipment. Both The Kubota, CAT, and Lombardini diesel are

1616GENERATOR7.5 kw and 8 kw models available60 hz and 50 hz models available FUEL REQUIREMENTSUse a clean No. 2 Diesel fuel oil (SAE J313

161617SPECIFICATIONSTRAILERThe engine-generator set is housed in a bunded two wheel trailer fabricated from heavy gauge steel. The design enables the

1818 BEFORE STARTING:1. Fill the engine with the right grade of lubricating oil (refer to the proper page of this manual or the Kubota, CAT, or Lomba

181819FOR A WARM ENGINE (Kubota, CAT, and Lombardini engines)Follow the same procedure as described for cold weather starting, skipping step 1 (step

22INSPECTION CHECK LISTFOR PREPARING THE NIGHT-LITE PROV SERIES FOR DELIVERY OR RENTALThe NIGHT-LITE PRO V SERIES requires service as well as proper o

2020SERIAL NUMBER LOCATIONGenerator: The generator has a plate attached to the side of the housing.Engine: The KUBOTA engine has the se-rial number st

202021NOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFig. 1 Control PanelFIG. 1. CONTROL PANEL (Kubota) 1. Breaker Switch Controls ligh

2222NOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFig. 2 Winch Switch and Breaker12FIG. 2. Winch Switch and Breaker (Electric Winch Mod

222223CONTROLS AND COMPONENTSNOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFIG. 4FIG. 5AFIG. 4. GROUND ROD LOCATION1. Ground rod shoul

2424FIG. 6BFIG. 6B ENGINE COMPONENT IDENTIFI-CATION (CAT)1. Water temp switch2. Alternator3. Starter4. Air cleanerFIG. 6A ENGINE COMPONENT IDENTIF

242425FIG. 7BFIG. 7A. ENGINE COMPONENT IDENTI-FICATION (KUBOTA cont’d)1. Oil ll2. Glow plugs3. Fuel solenoid4. Electric Fuel Pump5. Fuel lter6.

2626NOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFIG. 8dFIG. 8d. REMOTE OIL DRAIN LOCATION1. Remote oil drain (all models)Remove cap

262627CONTROLS AND COMPONENTSNOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFIG. 8FIG. 9FIG. 8 REAR PANEL 1. Rear Panel2. Serial Num

2828FIG. 10FIG. 10 POSITIVE DOOR LATCH 1. Positive door latchLocks door in the open position1CONTROLS AND COMPONENTSNOTE: PHOTOGRAPHS MAY SHOW NON-ST

282829FIG. 12aFIG. 12FIG. 12a. ELECTRIC WINCH 1. Safety Cover Installed (Left side view)FIG. 12bFIG. 12 ELECTRIC WINCH1. Electric Winch—Used to rais

223INSPECTION CHECK LIST ...2TABLE OF CONTENTS ..

3030CONTROLS AND COMPONENTSNOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFIG. 15. LIFTING ATTACHMENT POINTS1. Forklift Lifting Pockets

303031CONTROLS AND COMPONENTSNOTE: PHOTOGRAPHS MAY SHOW NON-STANDARD EQUIPMENT AND OPTIONSFIG. 16FIG. 17 and 17a Light Bar and Mounting Locations1. Li

3232ROUTINE MAINTENANCEKUBOTA D905, D1105, CAT C1.1, and LOMBARDINI LDW 1003 INSPECTION AND LUBRICATION SCHEDULECheck condition of the steel cable and

323233DANGER!HIGH VOLTAGE! DO NOT ATTEMPT TO TEST AND REPAIR GENERATOR AND BAL-LAST ELECTRICAL SYSTEMS UNLESS YOU UNDERSTAND AND ARE QUALIFIED TO WOR

34LIMITED WARRANTYALLMAND LIGHTING SYSTEMSLIMITED WARRANTYUNITED STATES and U.S. TERRITORIESTHIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES

44This manual provides the information necessary for the safe operation of the Allmand Bros., Inc., NIGHT-LITE PRO V Series light tower.The NIGHT-

445SAFETY AND WARNING DECALSSAFETY WARNINGALWAYS REPLACE ANY SAFETY AND INSTRUC-TION DECALS THAT BECOME DAMAGED, PAINT-ED, OR OTHERWISE ILLEGIBLE.

66SAFETY AND WARNING DECALSPART NO. 090158Location: Inside left hand door panel.PART NO. 090166Location: Side panel on manual winch models.PART NO. 09

667ELECTRIC WINCH VERTICAL MAST OPERATIONDESCRIPTION OF OPERATIONThe Allmand NIGHT-LITE V Series tower as-sembly consists of a seven section telescop-

881. Remove the electrical power from the winch. (Switch Electric Winch Switch to OFF)2. Insert the handle so that it completely engages with the dr

889PURPOSE1. Adjustment of the winch clutch nut is necessary to limit the power of the winch. The clutch nut must be tight enough to prevent clutch